Text from the interactive explanation
Intrinsic polarization superjunctions in III-nitride heterostructures for efficient power electronics
Luca Mazzone, Yuan Zong, Hongkeng Zhu, Alessandro Mauro, Elison Matioli
Original paperIntrinsic polarization superjunctions · Nature Electronics 2026
A gallium-nitride power diode must hold thousands of volts across a 25-µm strip when it is off. Raise the voltage, watch where the field goes, then give every electron a matching hole.
Field: TCAD simulation from the paper (Fig. 1d,e), interpolated between the published curves; the area under it equals the blocking voltage. Cross-section, carriers and sparks are illustrative and not to scale.
Below the critical field
measured In the lab (Ext. Data Fig. 1): the no-hole diode broke at 764 V; the matched iPSJ diode held 3.9 kV.
electron (2DEG)
mobile hole (2DHG)
fixed positive charge
other extreme, same voltage
The idea
Every electron needs a partner
Gauss's law in one sentence: wherever net charge is left behind, the field must change, so a neutral region keeps the field level. Blocking voltage sweeps the electrons out. What stays behind decides the shape of the field.
1
On: paired with fixed charge
In a conventional GaN diode the 2DEG electrons (about 1013 per cm²) are balanced by fixed positive charges located at the surface and within the buffer. At 0 V every electron has a partner and the strip conducts.
2
Off: the partners can't leave
Switch off and raise the voltage: electrons run to the cathode, but fixed charges stay. The depleted zone is left positively charged, so the field climbs into a spike at the anode edge, far above GaN's critical field, while most of the strip carries almost nothing.
3
iPSJ: partners that leave together
A thick undoped GaN cap uses built-in polarization to induce a 2D hole gas matched to the electrons. Through an ohmic hole contact (p-Ω) both carriers leave together, nothing is left behind, and the same voltage spreads evenly over all 25 µm.
measured Holes barely conduct (Hall mobility ≈ 12 cm² V⁻¹ s⁻¹ versus 1,832 for the electrons), so they balance charge without slowing the on-state: the diodes keep 4.7 mΩ cm² and a 0.75-V turn-on.
Simulated · TCAD (Fig. 1c, Extended Data Fig. 4)
Grow the cap, summon the holes
The polarization that creates the electron sheet can also create a hole sheet, if the undoped GaN cap above the barrier is thick enough. No intentional doping is needed: the cap thickness sets the balance.
—
Simulated with Silvaco ATLAS TCAD in the paper (Source Data, Fig. 1c). Mismatch is the net fixed charge left unbalanced, divided by Ns. The stack drawing is illustrative.
Surface traps try to steal the balance
Real surfaces carry donor-like trap states (density Dit). On a thin cap they pull charge from the sheets and reopen the mismatch; a thick cap decouples them.
—
Simulated (Extended Data Fig. 4): mismatch versus donor-like surface-trap density for two trap energies.
Measured · Extended Data Fig. 1, Fig. 2c–e
Breakdown bench
Three Schottky diodes with the same 25-µm drift length and the same 4.7 mΩ cm² on-resistance. Only the charge balance differs. A voltage ramp replays the measured off-state current until each one gives up.
—
Measured points · illustrative mechanism (Fig. 3, Fig. 4f)
Switch it hard
A power device spends its life flipping between blocking and conducting. The paper's harsh test holds each device off at a blocking voltage for 1 s, switches it on for 1 ms, and compares the on-resistance with its static value. Trapped electrons make it rise.
Diodes
Transistors
—
Points: measured normalized dynamic RON (1 s off at the blocking voltage, then a 1-ms on-pulse), one representative device per type (Fig. 3a,b; transistors Fig. 4f, setups as published). Left strip: illustrative mechanism described in the paper, not a measurement. Faint traces are devices you viewed earlier.
Measured · benchmark (Fig. 5)
Where it lands
Power devices trade on-resistance against breakdown voltage; lower-right is better. Charge matching moved the same diode from 342 V to 764 V to 3.9 kV without raising its on-resistance.
This work (iPSJ)
Literature SBDs
Literature D-mode transistors
Literature E-mode transistors
Material limits (4H-SiC, GaN)
Hover or focus a point.
Literature points re-plotted from the paper's Source Data for Fig. 5 (lateral GaN-on-Si devices). iPSJ values from the paper's text. The matched devices' breakdown was limited by the GaN-on-Si buffer, not by the superjunction itself.
Source
Luca Mazzone, Yuan Zong, Hongkeng Zhu, Alessandro Mauro & Elison Matioli. “Intrinsic polarization superjunctions in III-nitride heterostructures for efficient power electronics.” Nature Electronics 9, 1058–1066 (2026). doi:10.1038/s41928-026-01691-4
Open access under a Creative Commons Attribution 4.0 International licence. Curves are re-plotted from the paper's Source Data (values rounded); hero field profiles are interpolated between the published TCAD curves for 3 kV and the published peak-field table. Device cross-sections, particles, sparks and trap animations are illustrative and not to scale.
measured fabricated devices on the bench · simulated Silvaco ATLAS TCAD from the paper · illustrative drawings that explain a mechanism
Type: Archivo and IBM Plex Mono, both under the SIL Open Font License.
Topics in this iPaper
Engineering
We use the approach to create gallium-nitride-on-silicon polarization superjunction Schottky barrier diodes with a breakdown voltage exceeding 3.9 kV
Abstract, page 1058
Physics
We use the spontaneous and piezoelectric polarization fields to induce matched mobile electrons in a two-dimensional electron gas and mobile holes in a two-dimensional hole gas
Abstract, page 1058
power electronics
III-nitride semiconductors combine a wide bandgap with low sheet resistance and, thus, can be used for efficient power electronics.
Abstract, page 1058
gallium nitride
III-nitride power devices are typically created with lateral architectures based on barrier/gallium nitride (GaN) heterostructures
Introduction, page 1058
superjunction
In this Article, we report intrinsic polarization superjunctions (iPSJs)—intrinsically charge-balanced SJs without intentional doping.
Introduction, page 1060
two dimensional electron gas
The spontaneous and piezoelectric polarization discontinuity at the barrier/GaN interface induces a two-dimensional electron gas (2DEG)
Introduction, page 1058
two dimensional hole gas
together with a thick, undoped GaN cap layer that induces a 2DHG at the opposite interface (GaN/AlGaN)
iPSJ devices section, page 1060
schottky barrier diode
The iPSJ SBDs exhibited a turn-ON voltage of 0.75 V and RON,sp of 4.7 mΩ cm2 (Fig. 2b) for a PSJ length (LPSJ) of 25 μm.
iPSJ SBDs section, page 1061
high electron mobility transistor
The charge-matched D-mode and E-mode devices sustained VBR of 3.5 kV and 3.4 kV, respectively (Fig. 4d).
iPSJ transistors section, page 1063
dynamic on resistance
The devices exhibit a near-ideal dynamic ON-resistance degradation of less than 15% up to 3 kV
Abstract, page 1058
technology computer aided design simulation
TCAD simulation was performed using Silvaco ATLAS, with default material parameters and the GaN FET model.
Methods, TCAD simulation, page 1064