Text from the interactive explanation
Framework for the fabrication of scalable, flat foldable, thick origami Kresling structures via non-rigid methods
David Claude Bershadsky, Glaucio Paulino
Original paperThick origami, built to snap
Could a shelter or a spacecraft part fold flat like paper, then click open?
From the research of D. C. Bershadsky and G. H. Paulino, “Framework for the fabrication of scalable, flat foldable, thick origami Kresling structures via non-rigid methods”, engrXiv preprint, version 2 (2024). doi.org/10.31224/3811
Drag up or down to pull the top plate, sideways to turn it. Let go and it snaps.
modelIllustrative parts after the paper's construction: four flush layers joined by double-pivot links (light grey), arms routed so they never cross when folded. The energy comes from a simplified bar-and-spring model; stiffness is an assumption. Measured prototypes are in the Evidence section.
Twist a paper tube and it folds itself flat
Wrap paper around two tubes, leave a gap and twist. The paper over the gap buckles into a belt of triangles and collapses into a flat ring. That belt is the Kresling pattern.
A similar pattern turns up in nature, in the air sac of a hawkmoth, where it expands and contracts like a set of bellows. Because the pattern is so simple and folds completely flat, engineers like it for deployable structures : things that travel packed and open where they are needed.
Notice that the top turns as the belt collapses. Folding and twisting are locked together in a Kresling.
illustrationThe same simplified geometry used throughout this page, drawn as thin paper.
Stop a real paper Kresling halfway and it won't stay put. It springs to one end or the other. Why won't it rest in the middle?
It clicks because there is a hill in the way
A Kresling has two comfortable positions: folded flat and fully open. In between, its panels have to stretch a little, and stretching stores energy. Picture a ball rolling on a landscape with a valley at each end and a hill between them.
Physicists call a system with two stable resting states bistable . A light switch is one; so is a hair clip. To move between the states you have to push over the hill, called the energy barrier . Push past its top, the tipping point , and the structure finishes the job by itself. That is the click.
Why must the panels stretch?
A flat sheet can bend freely, but it cannot curve in two directions at once without stretching. That rule is Gauss's Theorema Egregium, and it is why an orange peel tears when you press it flat. Moving between the two Kresling shapes demands exactly that kind of change. So the pattern is not truly rigid origami: something besides the creases has to give.
modelIn the scene the serpentine springs in the upper arms (blue, turning orange as they stretch) provide the stretching the panels cannot. The curve is the simplified model's energy for a 6-sided design.
Your score: 0 / 0
Paper can stretch a tiny bit, so paper Kreslings click. Now build one from something thick.
Thick panels refuse, twice
Thin paper hides two problems that thick plastic, wood or metal cannot. Thick panels are usually rigid, so they won't stretch. And the folded layers no longer fit inside each other.
Problem one: rigid panels lock
Rigid panels: stuck in the folded state.
Problem two: layers pile up
The four-layer rule
Ni ≤ Nf + 1
The number of material layers overlapping at any point (Ni) can be at most the number of folds along the height (Nf) plus one. Each fold up the side makes room for one more layer in the flat stack. You can feel this when you fold a sheet of paper in half again and again: the stack quickly gets too thick to fold. The Kresling has three such folds (bottom edge, middle diagonal, top edge), so no point may hold more than four layers .
The authors' fix: remove material from the faces so the parts in each layer snake around each other , while every crease stays exactly where it was. A bonus: with no collisions left, the whole thing could in principle be 3D printed in one go, already folded flat.
Switch the heatmap to trimmed, routed arms to see this page's version of the trick. The lower arms each stay inside their own triangle; the upper arms curl out from the middle fold like a pinwheel, each one passing its neighbours without touching. Whatever the number of sides, the count never goes above four.
modelBoth heatmaps count overlaps in the flat state of this page's simplified geometry: solid, untrimmed panels, or the trimmed parts drawn in the 3D scenes.
The layer problem is solved with geometry. The stretching problem needs a different kind of hinge.
Hinges that bend instead of pivot
In paper, a crease comes free. In thick material, every crease has to be engineered. The paper compares four ways to do it.
Range
The living hinge is the key ingredient. Because it relies on the material's own elasticity, it can flex along several directions, not just around one pin. That lets a thick panel compress, stretch and bow slightly: exactly the give the Kresling needs to get over its hill.
after Fig. 2Schematic side views redrawn from the paper's Figure 2. Red marks where panels collide.
The living hinge as a spring
illustrationForce uses the page's assumed stiffness (0.8 N/mm for 8 bends). The trend, not the number, is from the paper: a longer living hinge needs less force and strains each segment less.
In the printed Kreslings, the living hinge is a serpentine spring of thin plastic walls in the upper arm of each side, just above the middle fold and set at right angles to the top and bottom plates. During each click it bows outward and twists. Changing its size, position and orientation tunes how hard the Kresling is to open.
PLA polylactic acid on a consumer 3D printer
0.4 mm nozzle, with 0.2 mm layers
3 walls continuous perimeters, no infill in the spring
Aligned extrusions run along the spring's stretch, for a longer life
Polygon plates, two arms per side, a living spring, at most four layers. That is the whole recipe. Now design one yourself.
Generate your own thick Kresling
Pick the polygon, side length, thickness and height. Every slider stays inside the range where the design still folds flat and still clicks, and the energy hill redraws as you go.
What sets the compatible range?
Both resting states must use the same bar and spring lengths. Folded, the four layers fix the stack at 4T. Opened, the paper's construction stands each pair of arms upright with the top plate square above the bottom; that fixes the tallest possible height, about twice the apothem (L·cot(180°/N)). Shorter designs stay twisted when open and their hill shrinks; as the open height approaches the folded stack, the two states merge and the click disappears.
How to read the plots
The energy curve is zero when folded and when open: those are the two valleys. Its peak is the barrier. On the force plot, the curve stays above zero while you have to pull, then dips below zero past the tipping point, where the stretched springs pull it open by themselves. The grey band marks where the printed prototypes tipped over (85–98% of full extension, measured).
modelThe curves come from a simplified bar-and-spring model of this geometry (illustrative): one rigid bar and one spring per side, stiffness assumed at 0.8 N/mm. It shows the shape of the hill and how it responds to the design, not the forces of a specific print. The 3D parts follow that model's height and twist, with the arm angles chosen so each serpentine stretches by the model's strain.
The model explains the click. Did real printed plastic actually do it?
What the printed prototypes did
The authors printed 3-, 4-, 5- and 6-sided thick Kreslings in PLA and pulled each one open in a modified Instron tensile tester. It measured the pulling force on the freely rotating top plate and the twisting torque on the clamped bottom plate.
measuredFigure 4c: six-sided thick Kresling being actuated in the tensile tester. Bershadsky & Paulino (2024), CC BY 4.0.
4 of 4 printed designs were bistable
85–98% of full extension: where each one tipped over
≈ 2 × r full extension, about twice the radius
Torque flip at the critical point, as tension turned to compression
The authors describe the structures as showing strong bistability, snapping easily between the two stable states once a critical strain is reached. The height of the barrier depends on the material's stiffness and on the spring design.
measuredValues read approximately from the paper's Figure 8d, where the barrier is the integral of force from zero displacement to where the force crosses zero.
Why the bars differ
The tipping point depends on many parameters at once: the number of sides, spring length and orientation, radius, side length and the elasticity of the printed plastic. The four samples differ in several of these, so the authors note they are not directly comparable. They still give intuition: short arms need little deformation and give a low barrier; longer arms and kinked springs need more.
Thick, flat-folding and still clicking. What could that make possible?
From paper to plastics, woods and metals
The authors show the thick version keeps what makes the Kresling useful: it folds fully flat, clicks between its states, and the hill can be tuned through the material and the design of the springy section, for example to absorb different amounts of energy.
Cancel the twist
Every Kresling turns as it opens. The twist adds up when units are stacked, so stacking units of opposite handedness cancels it. The middle plate turns, the top plate rises straight up.
modelTwo units of the simplified 6-sided design, stacked.
Deployable shelters
Flat-foldable shelters that ship as a stack and open on site.
Building with prefab parts
Prefabricated assemblies for constructing larger buildings.
Deployable spacecraft
Structures that launch folded and open in orbit.
So, could a shelter or a spacecraft part fold flat like paper and then click open? This work takes a concrete step: it shows how to keep the Kresling's flat fold and its click when the panels are thick. The authors see the same hinge and living-hinge techniques carrying many other classic thin origami patterns over to thick structural materials, such as plastics, woods and metals, opening the way to larger and more complex deployable structures.
In this study each part was printed separately and assembled; printing a whole Kresling in one piece, already folded flat, is proposed as a next step.
Sources and credits
D. C. Bershadsky and G. H. Paulino. Framework for the fabrication of scalable, flat foldable, thick origami Kresling structures via non-rigid methods. Engineering Archive (engrXiv) preprint, version 2 (posted 17 July 2024, updated 7 October 2024). DOI: 10.31224/3811. Preprint page: engrxiv.org/preprint/view/3811. License: CC BY 4.0.
Figures
Figures 1, 4, 6, 7 and 8 are reproduced from Bershadsky & Paulino (2024) under CC BY 4.0; cropped, resized and recompressed. Barrier values in the evidence chart are read approximately from Figure 8d.
About the interactive model
The energy and force curves on this page come from a simplified bar-and-spring model of the paper's geometry, built for this page: rigid bars, one spring per side, a single folding motion. The spring stiffness (0.8 N/mm for a spring-length factor of 1) is an assumption chosen for illustration, so the curves show the shape of the energy hill and how it responds to the design, not the forces of the printed prototypes. The geometry uses the paper's construction (γ = 360°/N, r = L / (2 sin(γ/2))) and its four-layer rule for the folded thickness. The 3D and 2D scenes draw the parts after the paper's description: a polygon plate at top and bottom, a lower arm and a spring-carrying upper arm on every side, and double-pivot links at the three folds so the layers lie flush when folded and open fully. Folded, the lower arms stay inside their own triangle of the polygon and the upper arms curl out from the middle fold like a pinwheel, so no two parts in one layer cross. These shapes were drawn for this page and are not the authors' CAD files. The arm angles are solved so that each serpentine stretches by the model's strain. The layer heatmap counts overlaps in the flat state, either for solid, untrimmed panels or for these trimmed parts.
References mentioned
S. Zang, D. Misseroni, T. Zhao, G. H. Paulino. Kresling origami mechanics explained: Experiments and theory. J. Mech. Phys. Solids 188, 105630 (2024). doi
B. Kresling. Natural twist buckling in shells: from the hawkmoth's bellows to the deployable Kresling pattern and cylindrical Miura-ori. IASS-IACM 2008 Proceedings.
R. J. Lang, K. A. Tolman, E. B. Crampton, S. P. Magleby, L. L. Howell. A review of thickness-accommodation techniques in origami-inspired engineering. Applied Mechanics Reviews 70 (2018). doi
A. S. Dalaq, M. F. Daqaq. Experimentally-validated computational modeling and characterization of the quasi-static behavior of functional 3D-printed origami-inspired springs. Materials & Design 216 (2022).
A. Pressley. Gauss' Theorema Egregium. Springer London (2010).
Typefaces: Instrument Serif and Inter, both under the SIL Open Font License.
Topics in this iPaper
Engineering
This work demonstrates a technique for creating non-rigid, fully flat foldable, and thick origami.
Abstract, page 1
origami
The fabrication of thick origami structures is usually rigid and not flat foldable.
Abstract, page 1
kresling pattern
These methods are demonstrated in a parametric model of a thick origami flat foldable Kresling pattern.
Abstract, page 1
living hinges
thick origami panels that selectively exhibit non-rigid behaviors can be fabricated using living hinges
Abstract, page 1
3d printing
By harnessing the material properties of 3D-printed Polylactic Acid (PLA)
Abstract, page 1
bistability
These Kresling structures exhibit strong bi-stability, easily snapping between stable points once a critical strain is reached.
Section 5 Preliminary Results, page 9
deployable structures
make it ideal for use in deployable structures
Section 1 Introduction, page 1